Tufnol Whale Plastic Sheet - 8mm To 15mm Thick

SRBF - Synthetic Resin Bonded Fabric

Mechanical Properties

• Compressive strength (edgewise): 200 MPa
• Compressive strength (flatwise): 310 MPa
• Cross breaking strength: 130 MPa
• Density: 1.36(sheet) 1.35(rod)/cm³
• Tensile strength: 68 MPa

Thermal Properties

• Maximum working temperature – continuous: 120°C
• Maximum working temperature – intermittent: 130°C
• Specific heat: 1.5 kJ/kgK)

What is Tufnol Whale Plastic Sheet?

Whale Tufnol Plastic Sheet is a grade specifically designed for mechanical engineering purposes. It is constructed of medium weave cotton and phenolic resin laminated plastic material. This particular grade is dimensionally very stable and can be either run dry or lubricated with water, oils or grease. It has excellent general physical properties with high strength, good toughness, and wear resistance. This grade is suitable for wear resistant components such as bearings, bushes, spacers and low voltage applications.

What is Whale Tufnol Plastic Sheet is used for?

This sheet is a most useful general purpose engineering plastic and is the most popular grade for a wide range of mechanical applications and general uses, such as gears, spacers, jigs and fixtures, wear resistant components, and low voltage insulation applications.

What should Whale Tufnol Plastic Sheet not be used for?

Whale Tufnol Plastic Sheet is not suitable for a high electrical insulation, circuit boards, and covers.

What are the advantages of Whale Tufnol Plastic Sheet?

Very Rigid with high strength and low weight
Good electrical and thermal insulation properties
Non-corrosive; can reduce corrosion in metal parts
Higher thermal expansion than many metals
Withstands heavy loads with minimal creep
Excellent weather resistance
Good resistance to chemicals, oils, solvents and hydrocarbons

What are the disadvantages of Whale Tufnol Plastic Sheet?

Used for electrical insulation, but at low voltages only
Maximum working temperature is only 120 to 130 degrees C
When machined, it creates a fine yellow dust

How well does Whale Tufnol Plastic Sheet perform?

Whale Tufnol Plastic Sheet material is produced much like plywood and, as a result, is quite rigid – as much as twice that of nylon. In fact, it is the inherent rigidity of Whale Tufnol that diminishes creep. Picture two flanges, one of nylon and the other of Whale Tufnol, and bolted a lid down onto each. After applying about 50 ft. lbs. of torque to the bolts, the lid on the nylon flange would eventually loosen as the nylon creeps. The bolts on the other lid with the Whale Tufnol flange would stay roughly the same.

How well does Whale Tufnol Plastic Sheet machine?

Unlike many plastics, Whale Tufnol Plastic Sheet cannot be melted to re-shape it. Finished components are made by machining using ordinary machine tools such as saws, drills, lathes, milling machines, or high-speed computer-controlled CNC machines. Whale sheet is easily machined to produce these finished components. One disadvantage when machining it is that it is quite dusty, and prolonged drilling may cause the material to melt and adhere to the drill bit. In addition, because of its plywood-like construction, more delicate machined components are subject to shearing along the lamination.

Is Whale Tufnol Plastic Sheet good for wear resistance?

This grade is the one that is well known for its very good wear resistance and toughness.

Is Whale Tufnol Plastic Sheet chemical resistant?

Whale Tufnol Plastic Sheet also has good resistance to chemicals, oils, solvents and hydrocarbons, although concentrated acids and alkalis will attack laminates.

Can Whale Tufnol Plastic Sheet be Glued and bonded?

While the selection of adhesive is dependent on the material being used, Whale Tufnol can be bonded to a variety of materials.

Is Whale Tufnol Plastic Sheet suitable for Food applications?

Tufnol should not be used in any food applications where it may come into direct contact with food products.

Are their any unique characteristics for Whale Tufnol Plastic Sheet?

It is made primarily of cotton sheets and phenolic chemical resin. Pre-soaked and cured cotton sheets are layered over each other until the desired thickness is achieved. Afterwards, these are then strongly bonded together under high pressure in a hot press, being crushed essentially, with up to three tones of pressure and then cured. A finished sheet of 25mm, for example, will have begun its life at 40mm in thickness before undergoing the press!

What is the size range and availability of Whale Tufnol Plastic Sheet

Tufnol Whale Plastic Sheet is available in brown/tan colour and in thickness from 1mm up to 50mm. although our sales team are easily able to obtain you much thicker material. In addition to the Whale brand Tufnol Plastic Sheet, we offer both the Kite brand and Tufnol’s 1P13 grade. Both types are available in thicknesses ranging from 1mm up to and including 25mm thickness.

Why should you choose this Whale Tufnol Plastic Sheet?

This grade is an excellent thermal barrier material both to prevent extreme heat and extreme cold form transferring. It is hard, rigid, strong, and lightweight – being about 1/5 of the weight of steel and half the weight of aluminium. It is a good electrical insulator and is also resistant to long-term immersion in water. It is exceptionally resistant to weathering - much more so than most other plastics - and so has been used for components in outdoor and marine environments for many decades without corroding or degrading.

Why not choose Whale Tufnol Plastic Sheet?

A downside to the production process of Whale Tufnol Plastic Sheet is that tolerances can vary quite a bit due to miscalculations on the number of sheets used, the actual thickness of individual sheets, and even variances in the pressure applied by the press or the in the steel press sheets. Therefore, it may not be suitable for applications requiring very minimal tolerances.

Is there a summary of Whale Tufnol Plastic Sheet?

Whale Tufnol Plastic Sheet is a cotton fabric laminate made from medium weave cotton and phenolic resin laminated plastic. It is known as a Synthetic Resin Bonded Fabric, or SRBF. Whale Tufnol is a good, general-purpose medium weave grade for mechanical applications. It has excellent all round strength, good toughness and wear resistance as well as thermal barrier properties. It is versatile, easy to work with, and displays outstanding rigidity.